Spn 1347 fmi 3.

SPN FMI COMPONENT P-CODE CONDITION; Displayed on instrument cluster Displayed on Digital Wrench diagnostic software; 29. 3. Accelerator Position 2 ... 1347. 3. Fuel Pump Driver Circuit. P0232. Voltage Above Normal, Or Shorted To High Source. 1347. 4. P0231. Voltage Below Normal, Or Shorted To Low Source. 1347. 5 ...Cummins ISC CM2150 (2007-09) Fault Code: 272 PID: SID 126 SPN: 1347 FMI: 3 Fuel Pump Pressurizing Assembly 1 Circuit - Voltage Above Normal or Shorted to High Source. High signal voltage or open circuit detected at the fuel pump actuator circuit.The SPN and FMI codes in the table below are not intended to be paired from left to right. There are several possible combinations of SPN and FMI codes. To use the table below, first write ... 1347 Suction Control Valve Circuit 1348 Fuel Pump Control Valve #2 1349 Redundant Fuel Rail Pressure Signal 1485 Pump Power Relay ...3 SPN 107/FMI 3 - GHG14 Air Filter Sensor failed high Check as follows: NOTE: This fault code is not calibrated for NAFTA Market. If this fault code is active, the Common Powertrain Controller (CPC) parameter is incorrectly set. 1. Connect DiagnosticLink ®. 2. Check for proper configuration of the CPC against the server information.

Page 193 and 194: SPN 1347, FMI 6 - Fuel Pump Relay C; Page 195 and 196: SPN 1213, FMI 5 - MIL Open Key On, Page 197 and 198: SPN 515, FMI 16 - RPM Above Fuel Re. ... SPN 91, FMI 3 - FPP1 Voltage High F. Page 295 and 296: SPN 520199, FMI11 - FPP2 Invalid Vo. Page 297 and 298: SPN 91, FMI 16 - FPP1 Higher than F.Page 193 and 194: SPN 1347, FMI 6 - Fuel Pump Relay C; Page 195: SPN 1213, FMI 5 - MIL Open Key On, Page 199 and 200: SPN 515, FMI 0 - RPM Above Spark Re; ... SPN 91, FMI 3 - FPP1 Voltage High F. Page 295 and 296: SPN 520199, FMI11 - FPP2 Invalid Vo. Page 297 and 298: SPN 91, FMI 16 - FPP1 Higher than F.Code SPN: 612- FMI 14 Byte 7:23 Byte 8:1. I thought this was a thermistor code and inspected thermistors. Low side thermistor had bare wires at the plug. Installed a thermistor kit for both thermistors, cleared codes, test drove, and returned to customer. Customer drove 5-6 hrs and ac not working, ac check light on. Code SPN 613 FMI 14 Byte 7:1 ...

For example using slash notation (SA/SPN/FMI) Fault: 11/1049/3 - Pressure Sensor 1 / Analog input 1 SA - 11 = Brakes - System Controller (ABS) SPN - 1049 = Brake Pressure Sensing Axle 1 FMI - 3 = Voltage above normal, or shorted to high source In this instance breaking down the code may help explain what's happening behind the scenes and ...SPN 3480/FMI 2 - EPA07 - EPA10 - GHG14 Step 8 was changed to refer tech to 3480/1 troubleshooting. Troubleshooting updated to lead tech to replace the Fuel Doser Injection Valve. Replace Fuel Doser Injection Valve if fault reoccurs during the validation step (parked regen). 3 07-15 All information subject to change without notice. 3

SPN 1188 - FMI 3 (Fault Code 465) REASON: High voltage detected at the wastegate actuator number 1 circuit. EFFECT: Engine power derate. The wastegate actuators are devices used by the Engine Control Module (ECM) to control boost pressure. The wastegate controller is located on the air inlet horn.Hi there again. Replaced the pressure sensor and fault is not there any more. The only ( inactive) fault that doesn't go away is fuel temperature too high . And we can not move the truck. Like if the pedal is not responding. But when we test the pedal it show on the computer as working properly. Technician: Nich M.Satisfied Customers: 8,405. Experience: Expert. Verified. Ask Your Own Medium and Heavy Trucks Question. FJ436658 I have problem with fuel codes Spn 1347 fmi 16. Technician: Nich M. Thank you. I'll be back soon with information on this fault. Ask Your Own Medium and Heavy Trucks Question.Code SPN: 612- FMI 14 Byte 7:23 Byte 8:1. I thought this was a thermistor code and inspected thermistors. Low side thermistor had bare wires at the plug. Installed a thermistor kit for both thermistors, cleared codes, test drove, and returned to customer. Customer drove 5-6 hrs and ac not working, ac check light on. Code SPN 613 FMI 14 Byte 7:1 ...

PowerView Model PV100 software version Murphy 2.09. 0710170. 12-13-07. Section 78. Note: This list represents text descriptions for faults supported by the PowerView and does not necessarily comply with. SAE J1939. For a specific engine manufacturer's explanation for codes, please consult the engine's technical manual. FMI.

SPN FMI; Engine Control Module: ... Or Shorted To High Source. 29. 3. Voltage Below Normal, Or Shorted To Low Source. 29. 4. Throttle Position Sensor 1. Data Valid But Above Normal Operational Range - Most Severe Level. 51. 0. ... 1347. 4. Current Below Normal Or Open Circuit. 1347. 5. Oxygen Sensor 1. Data Erratic, Intermittent Or Incorrect.

I have this weird issue on my 2014 MX-13. She will throw a code for SPN-5112 Controller #6 and SPN-153848. The Seek Service will stay on for a few days then go away. However a few days later it returns again. We have been playing this game for the last two months, but the truck has been running great.SPN 1321, FMI 3 - Start Relay Coil . Page 189 and 190: SPN 1348, FMI 5 - Fuel Pump Relay C. Page 191 and 192: SPN 1347, FMI 5 - Fuel Pump Relay G. Page 193 and 194: SPN 1347, FMI 6 - Fuel Pump Relay C. Page 195 and 196: SPN 1213, FMI 5 - MIL Open Key On, Page 197 and 198: SPN 515, FMI 16 - RPM Above Fuel Re. Page 199 and 200:SPN 677 (MCM)(EPA07) SPN 677 (MCM)(EPA10) SPN 677 (MCM)(GHG14) April 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform SPN 677/ FMI 5 - EPA07 The diagnostic procedures have been updated, wiring diagrams have been added and a software update has been added for GHG14.SPN 103 - FMI 15 (Fault Code 2288) Blog.Teknisi. Subscribe to receive free email updates: 1 Response to "SPN 633 - FMI 11 (Fault Code 2311)" Anonymous Tuesday, August 15, 2023 at 3:03:00 PM PDT. Nadjib [email protected]. Reply Delete. Replies. Reply. Add comment. Load more...FMI 3 – Voltage Above Normal or Shorted High: TECU detects a short to voltage or an open circuit for at least 1 second. Fallback: FMI 3, 4: • “F” flashes in gear display. • Service light flashes (if equipped). • Engine will not crank. Conditions to Set Fault Code Inactive:I have a Cummins motor with fault codes SPN 1387 FMI 3 and SPN-157 FMI 18 can you tell me what is wrong ... Yesterday morning, it started getting the code SPN 1347 FMI 3. The code went away last night and hasn't come back. I looked it up on Cummins insite so I k ...Refer to OEM literature and repair the wire between the ACM and the line heaters. Verify repair. 4 SPN 3599/FMI 4 - EPA10. High Side Digital Output 3 Circuit Failed Low. Table 3. SPN 3599/FMI 4. Description. This Code Sets When the Aftertreatment Control Module (ACM) Detects a Short to Ground on Pins 9, 15, or 39.

SPN 920, FMI 3 - Buzzer Control Sho. Page 285 and 286: SPN 1213, FMI 4 - MIL Control Groun. Page 287 and 288: SPN 1213, FMI 3 - MIL Control Short. Page 289 and 290: SFC 638-Throttle Unable To Close Ke. Page 291 and 292: SPN 91, FMI 18 - FPP1 Lower than FP. Page 293 and 294: SPN 91, FMI 3 - FPP1 Voltage High F. Page 295 and 296:CODES: Fault Code: 2367. PID (P), SID (S): S80. SPN: 1073. FMI: 3/3. Lamp: Amber. REASON: Engine Brake Actuator Driver Output 2 Circuit - Voltage Above Normal or Shorted to High Source. Open circuit or high voltage detected at the engine brake solenoid number 2 signal circuit. EFFECT: Engine brake on cylinders 4, 5, and 6 can not be activated.Disconnect the x2 connector when checking resistance. Pin 9 is the common. Pin 13 is the release and pin 10 is the hold. First test measure ohms across the x2 connector pins 9 and 13, you should have 4.9 to 5.5 ohms. 2nd test check ohms at the x2 connector pins 9 to 10 and you should have 4.9 to 5.5 ohms. 3rd test check pins on the x2 connector ...SPN 51, FMI 3 - TPS1 Signal Voltage. Page 55 and 56: SPN 108, FMI 1 - BP Low Pressure In. Page 57 and 58: SPN 3217, FMI 5 - EGO1 Open/Lazy (H. Page 59 and 60: ... Page 193: SPN 1347, FMI 6 - Fuel Pump Relay C; Page 197 and 198: SPN 515, FMI 16 - RPM Above Fuel Re;3. Let the engine idle for 5 minutes. 4. Fault code status will become pending with one detected failure and active with the second. NOTE: Do not use the idle speed balance (ISB) test in the diagnostic service tool for any misfire at idle testing. POSSIBLE CAUSES: 1. Valve lash out of adjustment. 2. Valve train damage/failure. 3. Bent valve. 4.

Fault Code: 275. PID (P), SID (S): S126. SPN: 1347. FMI: 7. Lamp: Yellow. REASON: Fuel Pumping Element Number 1 (Front) - Mechanical System Not Responding Properly or Out of Adjustment. EFFECT: Engine will not run or possible low power. Circuit Description: The fuel pump contains two barrel and plunger assemblies; each barrel and plunger ...SPN: 653 | FMI: 7 Injector Solenoid Driver Cylinder 3 - Mechanical System Not Responding or Out of Adjustment. Thoroughly inspect the injector wiring between the engine control module and your fuel injection solenoid's for any corrosion or damage that would cause a short or open circuit. If there's no problems with the injector wiring, The most ...

Fault Code: 275. PID (P), SID (S): S126. SPN: 1347. FMI: 7. Lamp: Yellow. REASON: Fuel Pumping Element Number 1 (Front) - Mechanical System Not Responding Properly or Out of Adjustment. …2016 freightliner m2 with 8.0l lpg. no signal power to the fuel pump relay and obviously truck will not start. code i have is spn 94- fmi 7 and spn-2634 fmi-5. if i bypass the relay the pump will run and solenoid opens but truck still won't run. helpIf fault code SPN#157, FMI#3 is. screen for fault code SPN#157, not displayed, turn keyless. FMI#3. engine switch to the OFF. position (TM 5-3895-385-10), remove ...Page 193 and 194: SPN 1347, FMI 6 - Fuel Pump Relay C; Page 195 and 196: SPN 1213, FMI 5 - MIL Open Key On, ... SPN 91, FMI 3 - FPP1 Voltage High F. Page 295 and 296: SPN 520199, FMI11 - FPP2 Invalid Vo. Page 297 and 298: SPN 91, FMI 16 - FPP1 Higher than F. Page 299 and 300:SPN: 77. FMI: 3. Rear Drive Oil Temp This DTC will be recorded when the control unit sees an open at the rear drive axle oil temperature sensor input. Possible Causes: 1) Broken wire 2) Corroded or disconnected connector 3) Sensor failure. The 524287 fault is coming from the predictive cruise control on the truck. All this specifies is there is ...Aug 2, 2018 · CODES: Fault Code: 271. PID (P), SID (S): S126. SPN: 1347. FMI: 4. REASON: High Fuel Pressure Solenoid Valve Circuit - Voltage Below Normal or Shorted to Low Source. Electronic fuel control actuator shorted low. EFFECT: Engine will run poorly at idle. Engine will have low power. SPN 3513 - FMI 3 (Fault Code 1695) SPN 3513 - FMI 4 (Fault Code 1696) Blog.Teknisi. Subscribe to receive free email updates: 0 Response to "SPN 101 - FMI 3 (Fault Code 1843)" Post a Comment. Newer Post Older Post Home. Subscribe to: Post Comments (Atom) Categories. Fault Codes CUMMINS ISB ISC ISL ISBe ISDe and …SPN 1347 FMI 6 Fuel Pump Relay Coil Short to Power 204 SPN 1348 FMI 5 Fuel Pump Relay Coil Open 198 SPN 1485 FMI 3 Power Relay Coil Short to Power 222 SPN 1485 FMI 4 Power Relay Ground Short 220 SPN 1485 FMI 5 Power Relay Coil Open 218 SPN 3050 FMI 11 Catalyst Inactive on Gasoline (Bank1) 161 SPN 3051 FMI 11 Catalyst Inactive on Gasoline (Bank2 ...

40018 11 January 2011 Compressors John Deere Fault Code 1347. MODEL. SERIAL NUMBER. John Deere. Tier III 4045HF285 engines Tier III 6068HF285 engines. Doosan Infracore would like to inform its dealers that the fault code 1347 for John Deere compressors listed above implies that the suction control valve (p/n 36139350) is stuck in open position.

SPN 1347, FMI 6 - Fuel Pump Relay C. Page 195 and 196: SPN 1213, FMI 5 - MIL Open Key On, Page 197 and 198: SPN 515, FMI 16 - RPM Above Fuel Re. ... SPN 91, FMI 3 - FPP1 Voltage High F. Page 295 and 296: SPN 520199, FMI11 - FPP2 Invalid Vo. Page 297 and 298: SPN 91, FMI 16 - FPP1 Higher than F.

I have a 2018 peterbilt with MX13. Tried died would not run, have codes SPN 1347 fmi 16. 156 fmi 3, 3480 fmi 17, spn94 fmi 10, spn 94 fmi 2. The company changed fuel filters that did nothing, I dont have any experinece on these truck. Not sure where to start or if Fuel rail could be problem? any insight would be great.DDC-SVC-MAN-0009 EPA07 Series 60 SPN 3598/FMI 3 This is a new section. DDC-SVC-MAN-0009 EPA07 Series 60 SPN 3598/FMI 4 This section is revised with additional steps. NOTE: Page numbers are based on the most recent version of the individual publication and may be adjusted throughout the annual print cycle.SPN: 653 | FMI: 7 Injector Solenoid Driver Cylinder 3 - Mechanical System Not Responding or Out of Adjustment. Thoroughly inspect the injector wiring between the engine control module and your fuel injection solenoid's for any corrosion or damage that would cause a short or open circuit. If there's no problems with the injector wiring, The most ...3 HE97192,0001B12 -19-07SEP07-1/10 Diagnostic Trouble Codes - CAB - Control Unit CAB and Cab Power Module Cont. SPN FMI Priority Description Go to 03 Park brake engaged indicator (cc# 519) has Section 240 - Electrical System - CAB 70 Warning voltage present when control unit CAB has Control Unit CAB/CPM Overall turned low side driver ON ...Cummins ISC CM2150 (2007-09) Fault Code: 281 PID: SID 126 SPN: 1347 FMI: 7 Fuel Pump Pressurizing Assembly 1 - Mechanical System Not Responding Properly or Out of Adjustment. Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe™ Online for applicable fixes to the ...SPN 876 FMI 5 - HVAC Compressor Clutch Engagement Undercurrent. Overview. This fault code sets when an A/C Compressor Clutch or Compressor Clutch Circuit fault is present. Possible Causes. I put a direct power current to the ac and the clutch engages fine. And it started to throw cool air.Section 7.1SPN 97/FMI 3. SPN 97/FMI 3 indicates a Water-in-Fuel Sensor open circuit.‪. Check as follows:‪. Check for multiple codes. If any EGR faults are active at the same time, repair the open circuit between pin 67 of the MCM 120-pin connector and pin 3 of the Water-in-Fuel Sensor. Refer to "7.1.1 Verify Repairs" .Section 82.2SPN 1172/FMI 3. This code is typically sensor or circuit failed high.‪. Check as follows:‪. Turn the ignition ON (key ON, engine OFF). Check for multiple codes. If 1172/3, 3250/3, 3242/3 and 3246/3 are present, go to the next step. If only 1172/3 is present, go to step 5. Disconnect the Turbo Compressor Inlet Temperature Sensor ...• SPN 94/FMI 15 or 16 Fuel Filter Plugged • SPN 157/FMI 1 Rail Pressure too High • SPN 164/FMI (All) Rail Pressure Sensor Faults • SPN 174/FMI 0 Fuel Temperature too High • SPN 1077/FMI 5 or 6 Quantity Control Valve Current • SPN 1077/FMI 14 High Pressure Leakage Too High • SPN 520251/FMI (All) PCV High Side Error

FMI SPN FMI DESCRIPTION QSB QSC QSL9 QSM1 1 QSX1 5 QSK19 QSK23 QS T 30 QSK45 QSK60 QSK78 HHP Level Number (**) 111 (Red) S254 12 629 12 ... 3 1347 3 High Fuel Pressure Solenoid Valve #1 Circuit X- shorted high 273 (Yellow) S127 4 1348 4 High Fuel Pressure Solenoid Valve #2 Circuit - shorted low X 274Dec 15, 2013. #1. I have a IR G 240 generator. When i load bank the unit and get about 150 kw of load the rpm starts to fall and i get a spn 1347 fmi 7 code. I have changed the mechanical fuel pump and the high press pump also the press sensor on the fuel rail with out success. Also checked the relief valve on the rail for leakage when running ...Detroit DD13 EPA10 (2010-13) Fault Code: SPN 4337 FMI 3 (ACM) Diesel Exhaust Fluid Metering Unit Temperature – Drift. NOTE: Please see the step by step troubleshooting procedures for this specific code. PROBABLE CAUSES: 1. DEF metering unit temperature sensor. 2. DEF metering unit temperature sensor connector/harnessInstagram:https://instagram. kathy and jim conrad net worthroute 75 trafficdr frank e ray sermonsgateway experience cia pdf Page 193 and 194: SPN 1347, FMI 6 - Fuel Pump Relay C; Page 195 and 196: SPN 1213, FMI 5 - MIL Open Key On, ... SPN 91, FMI 3 - FPP1 Voltage High F. Page 295 and 296: SPN 520199, FMI11 - FPP2 Invalid Vo. Page 297 and 298: SPN 91, FMI 16 - FPP1 Higher than F. Page 299 and 300: n 400 case is being actively reviewed by uscisslice master cool game 3: sensor volt2 (+5vdc)above norm or short high: 1080: 4: sensor volt2 (+5vdc)below norm or short low: 1109: 31: eng prot system approaching shutdown: 1110: 31: eng prot system shut eng down: spn fmi description; 1347: 5: fuel pump assy 1 ckt open, shorted ground or ovload: 1347: 7: fuel pump assy 1 rail pressure cont mismatch: 1347: 10: fuel ... nashua nh police scanner These repair instructions are intended to address the following fault(s): DTC. Description. Possible Cause. Possible (Observable) Symptoms. SPN 3027 FMI 3. Transmission Fluid Level Sensor Circuit High - Voltage Above Normal or Shorted High.CODES: Fault Code: 272. PID (P), SID (S): S126. SPN: 1347. FMI: 3. SRT: REASON: Fuel Pump Pressurizing Assembly 1 Circuit - Voltage Above Normal or Shorted to High Source. High signal voltage or open circuit detected at the fuel pump actuator circuit. EFFECT: Engine will NOT run or engine will run poorly.